top of page
Search
Diagram of how a leisure battery is charged: mains hook-up charger, alternator through a DC-DC charger, and solar panel through an MPPT controller, all into the leisure battery. LVA, Penryn, Cornwall.

In-Depth Leisure Battery and Charging Guide

16 hours ago
12 min read

This guide goes further than the basics. It covers how to read a lead acid battery's voltage, when damage starts, lithium (LiFePO4) rules, how to size a battery, and how to charge from mains, the alternator and solar.


If you want the short version first, start with our leisure battery basics for beginners.


You can buy a battery two ways:



Figures below are typical makers' figures at about 25°C. Different batteries vary, so always follow your own battery's label or manual.


Reading your battery's voltage


A voltmeter is a useful guide to how full a lead acid battery is, but only if the battery has rested for several hours with nothing charging it and nothing switched on. Makers' state-of-charge tables assume a rested battery.


Typical 12V lead acid resting (open-circuit) voltages, at about 25°C:


State of charge

Wet (flooded) lead acid

AGM

100%

12.65V or more

about 12.84V

75%

12.45V

12.54V

50%

12.24V

12.24V

25%

12.06V

11.94V

0% (fully discharged, at rest)

11.89V

11.64V


These figures come from well-known makers' guides. A cold battery reads a little lower, so treat the table as a guide.


Chart of typical 12V lead acid leisure battery state of charge from resting voltage at about 25°C, comparing wet flooded and AGM batteries. Typical figures — follow your battery's manual. LVA, Penryn, Cornwall.

What 10.5V means. 10.5V is the cut-off voltage under load that makers use when they test a battery's Ah rating, at the 20-hour rate. When the load is taken off, the voltage bounces back up.


A fully discharged battery at rest reads about 11.6V to 11.9V. If you see 10.5V while things are switched on, the battery is flat, so switch off and recharge it straight away.


What a full battery reads. A full lead acid battery at rest is typically about 12.6V to 12.8V. Some makers give 12.65V or more for wet batteries, and about 12.84V for AGM.


Readings of 13.2V and above. A reading of about 13.2V to 14.7V does not show a higher state of charge. It usually means one of two things:


  • It's on charge. A charger, solar panel or engine is connected. Chargers hold a battery at its float voltage (about 13.5V to 13.8V) or its absorption voltage (about 14.4V to 14.7V) while charging.

  • Surface charge. Just after charging, a battery shows a higher voltage for a while. Let it stand for about an hour, or better still a few hours, before testing.


To get a true reading, disconnect the charger and switch everything off, then wait a few hours before you measure.


When to recharge lead acid. Recharge it as soon as you can after every use. Try not to go below 50% (about 12.2V at rest), which is the level the NCC and the caravan clubs base their advice on. Many makers advise recharging whenever a leisure battery falls below 12.4V, which is just under 75% on the table above.


Compare types on our leisure batteries, delivered page, or ask in our Penryn shop.


When does damage start?


Lead acid (wet, EFB, AGM and gel) is damaged by sulphation. When it's left partly or fully discharged, hard sulphate crystals build up on the plates and don't fully dissolve when you recharge. This loses capacity for good.


  • Irreversible damage can happen if a battery sits at or below 12.4V for long periods, or is deeply discharged.

  • By about 12.0V, makers describe the effect on battery life as severe.

  • The deeper you discharge each time, the fewer cycles you get.


Lithium (LiFePO4) doesn't suffer from sulphation, and it is built to be used much more deeply. Its two main risks are different:


  • Being left flat. After the BMS cuts out on low voltage, the battery still loses a little charge on its own. If it isn't recharged promptly, cells can be damaged by low voltage, permanently reducing capacity and life.

  • Charging below freezing. See the cold weather advice below.


The BMS protects against both: it disconnects the battery when it's nearly empty, and it blocks charging when it's too cold. It still pays to recharge straight away after a low-voltage cut-out.


Typical cycle life, from makers' datasheets, is often 70 to 200 cycles at 50% discharge for wet leisure batteries, 150 to 225 for EFB, and over 360 for AGM. Quality AGM deep-cycle examples include around 600 cycles at 50% discharge and 400 at 80%. Lithium LiFePO4 examples include around 5,000 cycles at 50% and 2,500 at 80%, counted to the point where the battery still holds at least 80% of its rated capacity.


Charts of leisure battery cycle life at different depths of discharge, comparing wet, EFB, AGM and lithium LiFePO4 figures from makers' datasheets. Typical figures — follow your battery's manual. LVA, Penryn, Cornwall.

Figures depend on the exact model and how it's looked after. The pattern is clear: lead acid lasts longest if you keep it well charged, and lithium can be used much more deeply for many more cycles.


See the delivered range, or ask in our Penryn shop.


Lithium (LiFePO4): what to know


Most lithium leisure batteries use lithium iron phosphate, written LiFePO4 or LFP, because it's more stable than older lithium-ion types. People choose it because it's lighter (a typical 200Ah lithium battery weighs around 20kg, against around 60kg for lead acid), you can use 80 to 100% of the capacity, and it lasts for many more cycles.


It's also sealed and maintenance free. The trade-off is a higher price at the start, and a few charging rules you have to follow.


105Ah LiFePO4 lithium leisure battery in a standard case, sold for delivery by LVA in Penryn, Cornwall.

What is a BMS?


A BMS (Battery Management System) is the electronics that protect a lithium battery. It watches each cell's voltage and the battery's temperature, and it controls charging and discharging. If something goes outside safe limits, it shuts the battery down before damage is done.


Every lithium leisure battery must have one. Most have the BMS built in. Never bypass or remove it.


Charging lithium


A lithium battery needs a charger that has a lithium (LiFePO4) profile, or a custom setting you can adjust to the battery maker's figures. That applies to the mains hook-up charger, solar, and charging from the engine. A typical mains example is 14.2V absorption and 13.5V float for a 12.8V lithium battery; always use the figures in your own manual.


Charge from the engine through a DC-DC charger, not a basic VSR or split-charge relay (see below). Your solar controller also needs a lithium setting, and an older PWM controller will often need replacing with an MPPT unit. Turn temperature compensation off, or set it to 0mV/°C; lithium doesn't need it.


If you're swapping from lead acid to lithium, check that every charger in your van, including any built-in charger, can be set to a lithium profile.


Lithium voltages and state of charge


A lithium battery's voltage is very flat across most of its range. It stays at about 13V or a little above for most of the time you're using it, then drops quickly when it's nearly empty.


This means a voltmeter is a poor guide to how full a lithium battery is. A reading that looks fine can hide a battery that's nearly empty.


Typical 12V (12.8V) LiFePO4 voltages, from makers' datasheets, are about 14.2V to 14.4V when charging (some makers allow 14.0V to 14.6V), about 13.5V to 13.6V on float, comfortably above 12.8V after a rest, and around 11.2V at the end of discharge, though some batteries cut off at 10V. Different makes have different figures, so always follow your own battery's manual.


Use a battery monitor instead. A shunt-based battery monitor counts the amp hours going in and out and gives you a true percentage. Many lithium batteries with a built-in BMS also show their state of charge in a phone app.


Some lithium batteries do not calculate state of charge themselves, so you still need a monitor. If you're moving from lead acid to lithium, set your existing battery monitor up for lithium, or its readings will be wrong.


Typical 12V LiFePO4 lithium leisure battery voltage ranges given in the guide, including charging, float, rested, in-use and BMS cut-off figures. Not a discharge curve, because the guide has no full voltage-versus-charge table. Typical figures — follow your battery's manual. LVA, Penryn, Cornwall.

How deep can I go? Much deeper than lead acid. You can routinely use 80 to 100% of a lithium battery's capacity. Some makers rate their LiFePO4 batteries for regular cycling down to 20% left, and even to 0% without major loss of life.


Cold weather: the 0°C charging limit


This matters in a UK winter. Don't charge a standard lithium battery below 0°C, as charging cells when they're too cold can damage them permanently. Some makers set a higher limit, such as +5°C.


Using the battery in the cold is less of a problem, and some can discharge down to -20°C. A good BMS will block charging when the battery is too cold, and self-heating batteries warm themselves up first. If your van is stored outside over winter, check the manual.


Safety


  • Buy a lithium battery with a built-in BMS, from a seller who can tell you its charging limits.

  • Fuse it close to the battery, and use cables sized for the current.

  • Keep it away from heat sources, and secure it so it can't move while you're driving.

  • If you're not sure, have an experienced auto-electrician or caravan engineer fit it.


We sell LiFePO4 lithium leisure batteries in the delivered range. Ask in our Penryn shop whether lithium suits your setup.


How to choose the right type and size


The main types


The beginners' guide summarises wet, EFB, AGM, gel and lithium. In short: wet and EFB need a breather pipe in the living space; AGM is sealed and is commonly recommended for motor movers; gel needs its own charge profile; and lithium needs lithium charging and the cold-weather limits.


Comparison of wet lead acid, AGM, gel and lithium LiFePO4 leisure batteries, covering usable capacity, weight, cycle life and typical charging voltages. Typical figures — follow your battery's manual. LVA, Penryn, Cornwall.

Some batteries in our delivered range may be gel. Gel batteries are not available to collect from the shop.


Victron 90Ah gel deep cycle leisure battery, sold for delivery by LVA in Penryn, Cornwall.

If you're looking for lead acid leisure batteries, including wet, EFB and AGM, we have options delivered, including NCC-verified batteries. We also have deep cycle and AGM batteries to collect from our shop in Penryn.


Gel batteries, where we have them, and NCC-class batteries are in the delivered range only. They are not in the shop yet, so they are not available to collect.


NCC Class A, B and C are explained in the beginners' guide. Look for the class on the delivered page. We do not describe individual class availability here beyond what's on that page.


What size (Ah) do I need? A simple worked example


  1. List what you'll run each day, and for how long. Multiply each item's watts by its hours. Here's a typical example used in makers' guides:

    • TV, 50W for 2 hours = 100Wh

    • 5 lamps, 10W each for 4 hours = 200Wh

    • Water pump, 20W for 30 minutes = 10Wh

    • Phone charger, 5W for 3 hours = 15Wh

    • Total = 325Wh per day

  2. Turn watt hours into amp hours. Divide by 12V: 325Wh ÷ 12V = about 27Ah per day.

  3. Allow for usable capacity (depth of discharge).

    • Lead acid (use 50%): 27Ah ÷ 0.5 = about 54Ah of battery per day.

    • Lithium (use 80%): 27Ah ÷ 0.8 = about 34Ah of battery per day.

  4. Multiply by the days you'll be off hook-up without recharging. For 2 days: about 108Ah lead acid, or about 68Ah lithium.

  5. Add some spare. Your real use will vary, and batteries lose capacity in the cold and as they age. Solar or driving will top the battery up as you go.


In this example, a 110Ah to 120Ah lead acid battery, or a smaller lithium battery, would cover a two-day trip off hook-up.


Also check:


  • Physical size: measure your battery box or tray, including the height. We stock some low-height batteries in the shop.

  • Terminals: check the terminal type and which side the positive is on, so your cables reach.

  • Motor mover: AGM is commonly recommended for motor movers and auto-levelling systems.

  • Your chargers: check that your mains charger, solar controller and any DC-DC charger have a setting for the battery type you choose.

  • Weight: check your payload, especially in a motorhome or campervan.


Searching for a leisure battery for a caravan near me? Our Penryn shop can help you match the size and type. You can also order from the delivered range.


Charging basics


Diagram of how a leisure battery is charged: mains hook-up charger, alternator through a DC-DC charger, and solar panel through an MPPT controller, all into the leisure battery. LVA, Penryn, Cornwall.

Mains hook-up charger


Most caravans and motorhomes have a built-in charger that works whenever you're on electric hook-up. A good smart charger runs in stages: bulk, then absorption, then float. Some also have a storage mode.


Many built-in chargers don't have smart charging profiles. A separate smart charger can be better, especially for winter storage.


Charge profiles and voltages


Each battery type needs slightly different charging voltages. That's why smart chargers, solar controllers and DC-DC chargers have charge profiles, usually called wet (flooded), AGM, gel and lithium (LiFePO4). Always select the profile that matches your battery.


Using the wrong one can undercharge or overcharge it. Using a charger that isn't compatible with an AGM battery can cause permanent damage and early failure.


Typical 12V charging voltages at about 25°C:


Battery type

Absorption / bulk

Float

Notes

Wet (flooded) lead acid

14.4V to 14.7V

13.5V to 13.8V

Some profiles use 14.4V for flat-plate wet, and 14.7V for wet lead-calcium.

AGM

14.4V to 14.7V

13.5V to 13.8V

Some profiles use 14.4V for flat-plate AGM, and 14.7V for spiral-cell AGM.

Gel

14.1V to 14.4V

13.5V to 13.8V

Often a slightly lower absorption voltage than wet or AGM. Follow the manual.

Lithium (LiFePO4)

14.2V to 14.4V

13.5V to 13.6V

No temperature compensation.


These are typical figures. Your battery's label or datasheet gives the exact settings. EFB is an improved wet battery, so check its datasheet for which profile its maker recommends. Lead acid chargers also adjust the voltage for temperature, which is normal.


Typical 12V charging voltages at about 25°C for wet lead acid, AGM, gel and lithium LiFePO4 leisure batteries, including absorption and float. Typical figures — follow your battery's manual. LVA, Penryn, Cornwall.

Alternator charging while you drive


In a motorhome or campervan, the engine's alternator can charge the leisure battery while you drive. Newer vehicles, especially Euro 5 and Euro 6, often have a "smart" alternator. Its voltage goes up and down, and it can switch off altogether, so the leisure battery may never charge properly.


DC-DC chargers


A DC-DC charger sits between the starter battery and the leisure battery. It gives the leisure battery a proper charge in stages from the alternator, even with a smart alternator.


It also keeps the two batteries separate when the engine is off, so your starter battery isn't run down. With lithium, it also protects the alternator from being overloaded.


Why lithium needs a DC-DC charger, not a VSR


Many older vans charge the leisure battery through a voltage sensitive relay (VSR) or split-charge relay. This is just a switch: it connects the two batteries when it senses the engine charging, and disconnects them when the voltage drops. That works for lead acid, but it isn't the right way to charge lithium.


A lithium battery has very low resistance, and it keeps drawing a high current instead of tapering off like lead acid, which can overload the alternator. A relay also can't run a proper lithium charge profile, and on many Euro 5 and Euro 6 vehicles a smart alternator's voltage is often too low to charge the leisure battery properly. Because lithium's voltage stays high, a standard relay can also fail to disconnect as it would with lead acid.


A DC-DC charger limits the current, runs the right profile, and still charges the leisure battery from a smart alternator. Lithium-specific relays exist for simple setups, but a DC-DC charger is widely described as the safer default.


MPPT or PWM solar controller?


There are two main types of solar charge controller:


  • PWM is basically a switch that connects the panel to the battery. This pulls the panel's voltage down to about the battery's voltage, so some of the panel's power is wasted.

  • MPPT keeps adjusting so it takes the most power the panel can give. It then converts that power to the voltage the battery needs. It can also take a higher voltage from the panels (for example, panels wired in series) and still charge a 12V battery.


In published maker tests, MPPT harvested 10% to 40% more power when the panels were cool (below 45°C), very hot, or in very low light, which covers most UK conditions. To get the full benefit, the panel voltage should be well above the battery voltage. In the UK, MPPT is usually the better choice, and you'll need one with a lithium setting if you switch to lithium.


Solar


A solar panel with a charge controller keeps the battery topped up, both off-grid and in storage. The Camping and Caravanning Club suggests a 30W or larger panel to keep a battery maintained over winter if the van has a tracker or alarm. Set the controller to match your battery type.


Not sure which battery suits your solar setup? See our delivered range, or ask at our Penryn shop.


Winter storage is covered in the beginners' guide. The short version: charge the battery fully, stop the drains, and keep it topped up. Don't charge a lithium battery below 0°C.


Need a new battery before the season? Order a leisure battery delivered, or collect one from our walk-in shop in Penryn.


Leisure batteries near you in Cornwall


If you've searched for leisure batteries for sale near me and you're in Cornwall, you can find us in Penryn, close to Falmouth, and easy to reach from Truro.



Leisure Vehicle Accessories, The Praze, Penryn, Cornwall, TR10 8AA. Tel: 01326 712041.


For the short, phone-friendly version, see leisure battery basics for beginners.


FAQ


What does a reading of 13.5V or more mean?


The battery is either on charge (a charger, solar or the engine is running) or it still has surface charge from recent charging. Switch everything off and let it rest for a few hours, then measure again.


Can I tell how full a lithium battery is from its voltage?


Not reliably. Its voltage is very flat across most of the range, so use a battery monitor (shunt) or the battery's app instead.


Can I charge a lithium battery in winter?


Not when it's below freezing. Don't charge a standard LiFePO4 battery below 0°C, and some makers set the limit at +5°C. A BMS or a self-heating battery will help. Always check your battery's manual.


Do I need a DC-DC charger?


If your motorhome or campervan has a smart alternator (common on Euro 5 and Euro 6 vehicles), or if you have a lithium battery, a DC-DC charger is strongly recommended. A basic VSR or split-charge relay isn't suitable for lithium.


Is an MPPT solar controller worth it?


Usually, yes, in the UK. Maker tests have found MPPT harvests 10% to 40% more power than PWM in cool weather or low light.


Can I put a lithium battery in place of my lead acid battery?


Often you can, but check that your mains charger, solar controller and alternator charging all have a lithium setting. Fitting a DC-DC charger is also recommended.


Where can I buy a leisure battery near me in Cornwall?


Visit our walk-in shop in Penryn, near Falmouth and Truro, at The Praze, Penryn, Cornwall, TR10 8AA. See the batteries to collect in Penryn, or have one delivered.


Tel: 01326 712041

 
 
 

Comments


bottom of page